Soudacompound FR
Add to quick accessProduct description
SOUDACOMPOUND FR is a gypsum-based, non-shrinkable mortar what can be mixed with water. Mortar can be mixed either for pouring or for spreading around the penetrations.
Shown product
Soudacompound FR 20l
What are you looking for?
Featured properties
- Prevents the spread of fire and smoke.
Good sound insulation properties, 62dB with 50mm thickness.
Suitable for use in most penetrations.
Withstands the weight load (1,5kN)
No shrinkage or cracking.
Easy to install – can be applied with a COX Jumbo press.
No maintenance required.
Works also in humid conditions.
Soudawrap P FR or Soudacollar P FR need to be used when installing with combustible materials.
Can be over painted.
Assets
Applications
- SOUDACOMPOUND FR gypsum can be used to seal the penetrations in fire-rated walls and floors. The product offers up to 4 hours of fire resistance.
Instructions
- Measure the correct amount of water in the container and gradually add Soudacompound FR in the water, stirring constantly until the mass is even. The water powder mixing ratio is 1: 3, for the pourable mass 1:2. Mix only the amount needed during the use of the product (10-20min). Operating and curing times are reduced by reducing the amount of water or increasing the temperature. Note that the installation must not be carried out at temperatures above 35 ° C. The curing time is normally about 30-90 minutes. Mixing in larger quantities with a drill bit, for smaller quantities can be
mixed manually.
Installation
1. Remove any loose material around the penetration.
2. Add gypsum to clean water and mix with either hand or mixer.
3.Pour the mass into the mold or spread with a spatula into the penetration.
4. Keep the sack dry and protect from potential shocks.
5. Clean tools and equipment with water immediately after use.
Floors:
1. Mixing ratio: 1 bag Soudacompound FR for, 12 litres of water (2,5:1). Do not mix thinner than 2:1.
2. Place the casting mold in the penetration to ensure the casting is tight and durable, and that the required casting thickness is achieved.
3. Pour the gypsum mixture into the casting mold until the required casting thickness is reached.
4. The reinforcement requires 12mm rods at maximum 200mm intervals.
5. The rods must be attached to the surrounding structure with a minimum of 50mm grip. Gypsum casting can be drilled and expanded to make changes to the bushing, and can be easily re-sealed. The recommended clearance around the penetrating structures and the penetration must be at least 50mm or half of the diameter of the penetrating structure Do not cast directly onto corrosion-sensitive metal surfaces. For metals such as copper and steel, use a primer, or separate from the casting with eg a protective tape. The metal pipes insulation can also be done contiunous.
Install casting support (eg mineral wool) below the floor opening and seal the gaps. When the floor is thicker than the fire stop, install the casting support so that the top of the fire stop is leveled with floor. Small openings can be blocked with mineral wool or fire acryl. First, apply a layer of n.10mm of pliable gypsum to the casting support and, after curing, pour the rest into the required thickness. Finish with a wet spatula.
Permanent installation with casting support:
50mm stone wool board is cut and inserted tightly into a penetration. Stone wool board should be as tight as possible to keep the casting support tight. The space requirement for the thickness of the fire gypsum must be noticed when installing. Small openings can be blocked
with mineral wool or fire acryl to prevent draining from mold before actual installation work.
Walls:
1. With spatula: 1 bag Soudacompound FR for 10 litres of water (3:1). The mixing ratio depends on the site conditions.
2. Add gypsum as recommended. Mold gypsum with a spatula, starting on the bottom of the penetration, ensuring the correct casting thickness. Continue to fill the penetration until it is filled. If necessary, repeat the treatment on the other side of the wall structure if the cast structure is divided into two parts in the middle of the wall.
Mix the fire gypsum and spread with a spatula or a filler press into a penetration to be sealed.
Soudacompound FR settles in 30-45 minutes and lasts for example walking after about 72h. Notice! With plastic pipes use Soudacollar P FR or Soudawrap P FR (see Technical Data Sheets).